Version 1.11.3:
- Added official support for the Paradigm Defiance S10 and Defiance S12 subwoofers
- Updated bundled firmware for Paradigm Defiance S10 and Defiance S12 subwoofers to version 1.1.378
- Updated bundled firmware for MartinLogan Dynamo 10, Dynamo 12, Abyss 8 and Abyss 10 subwoofers to version 1.1.378
- [macOS] Firmware updates are only offered for direct USB Connections, not Bluetooth LE

Version 1.11.2:
- Initial Windows 11 on ARM support (through x64 emulation). Direct USB connections to devices are not supported, network only
- Added firmware update checks when connecting to systems that support it (such as: Anthem MRX SLM (Version 1.3 or later) and Paradigm SVX-1202 (Version 1.3 or later))

Version 1.10.5:
- Official support for the MartinLogan Dynamo 10, Dynamo 12, Abyss 8 and Abyss 10 subwoofers
- Fixed app hang that could occur when making changes to old arc files or when working with x20/x10/str save files
- Fixed app crash that could occur when closing the app or opening another save file when there are outstanding changes to the current screen
- Various quality of life improvements

Version 1.9.5:
- MRX x40/AVM70/AVM90/MRX SLM: fixed an issue that could cause abnormally high measurement levels during auto phase or quick measure with processing enabled, requires a re-upload of your saved ARC file to take effect
- Optimized thresholds for subwoofer level warning on systems where it was not strictly necessary (relative speaker level adjustments were still possible)

Version 1.9.4:
- Bundles new XR 11 and XR 13 firmware version 1.1.103

Version 1.9.3:
- Fixed a dependency issue that was preventing 'check for updates' from working on windows machines

Version 1.9.2:
- Added official support for the SVX-1202
- Minor bug fixes and improvements

Version 1.8.4:
- Added official support for the MRX SLM
- Fixed an issue where on file open the correct distance units were not always used
- Fixed an issue where ARCG could crash on exporting a PDF
- Minor bug fixes and improvements

Version 1.7.4:
- Added official support for the Defiance XR 11/13

Version 1.6.10:
- STR: updated bundled fw to 1.8.30. Fixes an issue with using the latest Anthem Remote app beta; added support for automatic time alignment.
- STR: re-upload the stored auto phase results every time a save file is uploaded (if auto phase has been run). Brings the STR series to feature parity with the MRX x40 series
- MRX x40/AVM70/AVM90/STR: added 'front left distance' and units to measurement configuration screen; ARCG will use these to convert from relative distances to absolute distances
- MRX x40/AVM70/AVM90/STR: a warning will be displayed if the measured delay exceeds that which is supported by the target
- MRX x40/AVM70/AVM90/STR: display the speaker distance (relative/absolute) that would be uploaded to a device in the 'levels' page
- MRX x40/AVM70/AVM90/STR: if present, export to PDF now includes speaker distances and subwoofer phase values
- Additional release notes from 1.6.1 onward: MRX x40/AVM70/AVM90/STR: uploaded subwoofer level is reduced by 4/6/8 dB for systems with 2/3/4 mono subs respectively
- Various bug fixes and improvements

Version 1.6.5:
- MRX/AVM/STR: fixed an issue where ARCG was sometimes targeting a 75dB SPL reference when it should not
- Fixed an issue where the application would deadlock on shutdown if the discovery screen was active at the time
- MRX x40/AVM70/AVM90: Known issue for host FW 68 or earlier: changing speaker profiles on the currently selected input does not fully take effect. The ARCEQ for the previous profile remains in place. Workaround: setup multiple identical virtual inputs with each one on a different speaker profile, then switch the current input to select different profiles

Version 1.6.4:
- Fixed an issue where calibration file download would sometimes fail
- MRX x40/AVM70/AVM90: fixed an issue where incorrect distances/levels were sometimes used during auto phase leading to incorrect results
- MRX x40/AVM70/AVM90: fine tuned the heuristic that selects the best phase value based on customer feedback
- Founder 120H: fixed a regression that prevented ARCG from completing a measurement on paired speakers

Version 1.6.1
- MRX x40/AVM70/AVM90: a new feature, automatic phase, distance and time alignment, has been enabled for beta testing
- MRX x40/AVM70/AVM90: host fw 68 or later is now required to run ARCG
- Other minor fixes and improvements

Version 1.5.4
- MRX x40/AVM70: various quality of implementation improvements, but requires host fw 56 or later
- MRX x40/AVM70: added support for performing quick measurements with processing applied (includes bass management and level calibration)
- Other minor fixes and improvements

Version 1.4.10
- Initial support for the Founder 120H
- Added the 'Pairing Tool'
- Various bug fixes and improvements

Version 1.3.25
- Initial support for the MRX 540, MRX 740, MRX 1140, AVM 70 and AVM 90
- Added support for the new ARC Pro microphone that ships the new AVRs and AVPs
- Improved handling of equalization at the max eq and min eq frequencies
- Fixed an issue where ARC would continue to try and perform measurements even if the initial setup failed
- Improved optimization speed and quality
- Update bundled firmware for the MartinLogan Masterpiece series to 0.1.9434
- Reset equalization screen fixed to show the correct prompt when it finishes or fails
- Added manual firmware update tool to support out of band updates for products that can only be updated using ARCG
- Some ongoing improvements for USB/Bluetooth devices in MacOS
- Other minor fixes and improvements

Version 1.2.3
- Fixed an issue where running ARC on a Persona 9H did not maintain a good balance between bass and midrange output. New measurements are required for the fix to take effect.

Version 1.2.2
- Fixed an issue where the 2nd/3rd/4th profile of multi-profile devices could end up with the wrong measured level
- Fixed discovery and/or connection with many USB subwoofers (a few combinations of product:os still have problems)
- Fixed upload failures with BalancedForce 210/212 on 32 bit windows
- Fixed the issue where bass boost center frequency, room gain center frequency and tilt start frequency were not reset to recommended values when auto detecting all target settings
- Fixed issue where the wrong value was being used for high frequency tilt start
- Changed SCM, app now follows major.minor.build - gitsha. Download files still must follow major.minor.build.rev but rev is now 0. so 1.2.2 == 1.2.2.0
- Fixed quick measure doesn't work on STR when processing = enabled
- Other minor bug fixes and improvements
Known Issues: Some loading screens still experience problems when 'canceling'.

Version 1.1.1.9105
- fixed issue where ARCG could measure an MRX x20 or AVM 60 at the wrong level
- fixed some issues with the formatting/layout of the title page on pdf reports
- fixed some issues relating to the Persona 9H
- fixed an issue where quick measure was not working reliably on the STR Integrated Amp or STR Preamp
- fixed an issue where quick measure was not working on the Paradigm PW 600/800/Amp/Link and MartinLogan Forte/Bravado/Unison 
- minimum high frequency tilt start frequency is now 5 hz (select '0 Hz' in UI)
- fixed issue where canceling an upload would not actually cancel until after it completed
- fixed an issue where ARCG would make a poor choice for high pass settings on subwoofers when more than one was measured (MartinLogan Masterpiece series, and 2 sub mono on STR series)

Version 1.1.0.9006
- added audio capture entitlement when signing macos version to prevent crash on macos 10.14.5
- request audio capture permission when first entering the microphone selection screen
- Added Spanish translations
- Added official Anthem MDX-8 and MDX-16 support
- fixed issue where the demo mode was using duplicate curves for position 1 and position 2 (1169)
- improved handling of changes to the speaker / measurement mapping (1455)
- prevent -0.0 from being selecte as a test tone level during the auto level sequence (1427)
- further improvements to always release exclusive control as soon as possible (1376)
- further refinements to calibration file download
- fixed Defiance X10/X12/X15 don't work over USB connections (1397)
- fixed issue where windows versions incorrectly required the user to have the vs2012 redistributable installed (1432)
- fixed auto phase adjust sweep output for STR Integrated R and L subs (1406)
- improved handling for when phase adjust needs arc upload (1333)
- decreased phase adjust sweep volume  (1334)
- added cancel button to the auto phase screen (1439)
- improved audio error handling on windows
- improved handling of usb errors (mac and windows)
- added automatic check for new ARC Genesis updates, prompts with option to open browser and download manually
- added option to enroll for beta releases (in preferences screen)
- increased STR profile name to allow up to 9 characters (maximum currently supported by STR IP commands)
- added notarization for mac OS builds to support mac os 10.14.5 or later
- added support for many older Paradigm Subwoofers (8872): DSP-3100, DSP-3200, DSP-3400, Signature SUB 25, Monitor SUB 10, Monitor SUB 12, Monitor SUB 8, SE Sub, SUB 1, SUB 2, SUB 12, SUB 15, UltraCube 10, UltraCube 12, X-300
- fixed Defiance X10/X12/X15 don't work (1397)
- MacOS: fixed an issue where microphones with serial number less than roughly 308000 would incorrectly measure at the maximum microphone volume (1410)
- fixed issue where ARC Genesis would measure 3 dB lower than ARC2 (1410)
- fixed an issue where ARC Genesis would not release exclusive control when leaving quick measure (1376)
- fixed an issue where ARC would claim to have downloaded the microphone calibration file, but it actully failed. (1405)
- MacOS: minor correctness fix in the face of errors when enumerating usb devices (650 and 800)
- MacOS: improved robustness of USB device support (650 and 800)
- fixed clicking cancel in the open file screen causes the app to crash (1392)
- fixed Tilt Start Frequency displays incorrect information in the PDF report (1418)
- fixed an app crash that occured if you clicked 'cancel' after getting communication errors durring the connecting screen (1424)
- fixed issue where app could crash after audio errors during measurment and the user went back to the home screen (1331)
- fixed an issue where scrollbars where not always showing in dropdowns (1411)
- fixed an issue where the 'Resume' was displayed instead of 'Start' in the measurement screen (1370)
- fixed typo correction 'Currected' to 'Corrected' (1409)
- added a loading indicator for quick measure initialization & removed visiblitly of unused graph title (1383)
- increased visibility of no microphone message
- info popup centered below info icon
- open file screen clears previous device image (1393)
- back button from mic selection screen returns to configure screen (1372)
- red error text fix for measurement screen
- fixed possible clipping in MRX x10/x20 when ARC is turned on (content dependent) (1415)


Version 1.0.1.8867:
- Added a new shortcut in the start menu that forces ARC Genesis to use the angle library rather than the GPU's (ims 1399)
- changes to preferences are commited on immediate exit (1371)
- loading indicator is now shown with device image image in middle on screen (1366)
- 'button' ui element can now support two lines of text (1380)
- removed duplicate completion text for reset eq screen (1373)
- added a browse for calibration file to mic selection screen (1390)
- fixed an issue where calibration files that included 'Anthem', 'Paradigm' or 'MartinLogan' in the filename were not supported (1390)
- fixed an issue where some code paths did not properly handle unicode text/paths (1390, 1391)
- added a web download link for manual calibration file download (1390)
- fixed the issue where some users were unable to download calibration files, or would get the 'critical audio problem' during the initialization phase of measurements (1390)
- filtered duplicate devices in the supported devices screen (1379)
- paired (left/right) MartinLogan Masterpiece series speakers now have a unique curve color for the left/right speaker (1384)
- fixed packaging of mac release where license.txt and firmware update files were not being copied to the application bundle (1400, 1378, 1398)


Version 1.0.0.8849:
- Initial 1.0.0 release